MARVL Maritime RobotX 2026

Vehicles / Quadrotor

22 inch quadrotor

The aerial vehicle, a quadrotor built in the lab on ArduPilot Copter. It maps the buoy field from above, relays the route to the boat, and carries resource tins to the delivery platforms. It is fitted with flotation because the course is over water.

Airframe

The airframe is a custom 22 inch quadrotor with carbon arms and plate, 22.4 by 8 inch two blade propellers, and foam flotation strapped along the arms and the body. The flotation keeps the aircraft upright and recoverable after a ditching. Two configurations are declared: the base aircraft, and the base aircraft with the tin grabbing assembly fitted.

  • TypeCustom quadrotor, multirotor
  • Dimensions98 x 89 x 29 cm, 129 cm diagonal
  • Empty mass6.6 kg
  • Operating mass6.8 kg with the delivery assembly
  • Propellers22.4 x 8 in, two blade, polymer and carbon
  • Flight controllerArduPilot Copter
  • Launch and recoveryVertical from the pontoon, water ditching if needed
The quadrotor from the front, propellers level, flotation foam under the arms.
Front view, delivery configuration.
The quadrotor from above showing the four arms, batteries and the centre plate.
Top view. Four battery packs sit inboard on the centre plate.
Close up of the underside of the aircraft where the delivery assembly mounts.
Underside mount for the tin grabbing assembly.
Foam flotation strapped along a carbon arm of the aircraft.
Flotation on the arms and body, sized to keep the aircraft upright in the water.

Power and endurance

Four 6S1P lithium ion packs in parallel, 4,500 mAh each, 18,000 mAh at 22.2 V in total. Flight testing at the delivery configuration mass gives about 18 minutes, so missions are planned to land by 15 with roughly three minutes in reserve.

Battery gates, from the safety behaviour documentation.
StageThresholdBehaviour
Take-off gate90%Team procedure: no launch below this state of charge
Low battery30%Warning and a return to launch prompt to the pilot
Critical battery20%Automatic land, controlled descent at the current position
Planned landing30%Missions are planned to land with at least this reserve

Control and telemetry

The manual link is a RadioMaster transmitter with a built in ExpressLRS module, paired to a receiver on the aircraft. It is independent of the ground station, so the pilot can take off, fly and land with the laptop switched off. The ground station runs Mission Planner for monitoring, mission upload and autonomous mission management. The operator console reports the aircraft to RoboCommand at 2 Hz, the same as the other two vehicles.

  • Manual linkExpressLRS 2.4 GHz, frequency hopping
  • Transmit power50 mW setting, about 0.08 W EIRP
  • Telemetry2.4 GHz to Mission Planner
  • Flight modesStabilise, AltHold, Loiter, Auto, Land, RTL
  • Declared ceiling50 m above mean sea level
  • GeofencePolygon with a 4 m internal buffer

Aircraft telemetry is also relayed to meet Singapore's network remote identification requirements, so every heartbeat has to carry the complete field set. This is one reason the RoboCommand client fills in flight phase, altitude and heading on every report, not only when they change.

The dedicated RadioMaster transmitter used for the aircraft.
The dedicated transmitter, assigned to this aircraft and the nominated pilot.

Failsafe behaviour

Failsafe triggers and responses.
TriggerDetectionResponse
Manual link loss5 s without valid inputLand: controlled descent at the current position, disarm on touchdown
Telemetry loss5 s without a heartbeatLand, with the pilot keeping manual control throughout
Navigation loss5 s without positionLand
Geofence reachedPolygon fence with a 4 m bufferBrake and hold at the boundary, in manual and in autonomous flight
Ceiling reachedFence altitude limitHold at the declared ceiling even when commanded above it
Mission abortGround station command or the pilot's mode switchLoiter or return to launch. A scored attempt does not resume after a manual takeover

The emergency stop on the transmitter cuts the motors immediately, on the ground and in the air. In flight it causes an uncontrolled descent, so it is used only when continued flight is the greater hazard.

Photograph of the aircraft with the safe handling areas marked.
Marked handling areas. The aircraft is picked up only at these points.

Delivery payload

Tasks 2 and 3 both end with a tin placed on a coloured circle. The delivery assembly is a removable tin grabbing mechanism of about 0.20 kg on an underside mount, powered from the main battery. The mount is drilled and the aircraft flies with it fitted. The grabber itself is still being finished.

The delivery tins are aluminium cans of 40 to 50 g coated in red, green or blue. The platforms are 2 m squares with 60 to 70 cm circles in the handbook's specified colours. The simulator draws these, and the perception work is trained on them.

Flight evidence

These are the flights submitted for the aerial proof of readiness. Each one runs start to finish with no cuts, as section 3.1.1 requires.

Autonomous mission1 min 25 sHandbook 3.1.4

Takeoff, the published pattern and landing, flown in Auto with the mode shown on the ground station.

Manual mission2 min 15 sHandbook 3.1.4

The same pattern flown by the pilot, with takeoff above 3 m and a landing back on the pad.

Geofence hold36 s

The aircraft is commanded past the boundary. It brakes and holds at the fence.

Link loss42 s

The transmitter is switched off in flight. After five seconds the aircraft lands automatically.

Positive buoyancy7 s

The aircraft in the pool, floating upright on its foam.

Motor testbench

Motor order and direction checked on the bench before flight.